Only For Calls this number won’t receive texts
+1 (386) 800 3366
+1 (386) 800 3366
Done wrong, blasting wood is a disaster – gouged grain, fuzzed fibers, ruined boards. Done right, wood sandblasting is the fastest way to take a gray, weathered log home, dock, fence, or set of beams back to clean, bright timber ready for stain or sealer. The whole thing comes down to control. Around Crescent City and Putnam County – lake cabins, old-Florida cottages, board fence, and dock structures – we restore a lot of wood, and here is how it is supposed to be done.
Mobile — We Come to You Our rig comes to your property anywhere in Putnam County — your lot on the lake, your barn, or your driveway.
Sealed the Same Day We prime or seal the same day we blast, so bare surfaces never sit exposed to the lake-country humidity.
Honest Advice First We tell you straight whether a piece is worth doing before we start — never upselling work you do not need.
Licensed, Insured & OSHA-Standard Contained, code-correct work on every job, from a single trailer to an industrial site.
Sun and moisture break down the surface layer of wood, leaving that silver-gray, fuzzy look and a layer of dead fibers, old finish, and mildew. On Crescent Lake and along the St. Johns it happens fast, because the damp never lets the wood fully dry. Under that weathered skin the wood is usually still sound – it just needs the dead layer and old coating removed so a fresh finish can soak in and protect it.
The secret to not wrecking wood is matching the media to the surface and backing the pressure way down – the core of good wood sandblasting. For timber we use a soft media – crushed walnut shell, corn cob, fine glass, or low-pressure soda – so we lift the gray layer, old stain, and mildew without carving into the grain. We always test a small, hidden spot first and show you the result, so you approve the look before we do the whole structure.
Log cabins need even, careful work across the rounded logs and the chinking between them. Docks and boardwalks want enough cleaning to take a finish without splintering the walking surface. Board fence is large-area work where consistency matters so the whole run stains evenly. Exposed beams and porch timber want a controlled finish – smooth or lightly textured, your call. We tune media and pressure to each.
Hand-sanding a log home or a long dock is brutally slow and never reaches the contours. Chemical strippers are messy, need neutralizing, and can raise the grain and leave residue that fights the new finish. Gentle blasting reaches every contour quickly and evenly – which is exactly why it is the tool of choice for log and timber restoration.
Freshly stripped wood is open and ready to drink up moisture, so it should be sealed or stained promptly – especially on the water. We coordinate the work so you can get sealer or stain on while the wood is clean and dry. See our coating service and, for a softer touch on delicate pieces, our green blasting. We work to OSHA standards on every job.
Wood is unforgiving of bad technique. Too much pressure carves troughs into the soft growth rings; the wrong, too-hard media fuzzes the fibers so the wood never takes stain evenly; holding the nozzle too close burns a divot. Every one of these comes from treating wood like metal. When you hear a company quote “sandblasting” a log home with the same setup they use on a trailer, that is the warning sign.
On the water, wood takes a beating from sun and damp. Docks and boardwalks need enough cleaning to take a fresh finish without leaving the walking surface splintered. Boathouses, railings, and pilings all weather the same way and restore the same way – gentle media, low pressure, even passes – so the whole structure takes sealer uniformly and is safe underfoot.
Blasting takes wood from gray and tired back to clean and bright, and it reaches contours sanding cannot. What it does not do is erase deep damage – if a log is rotted or a board is structurally gone, blasting reveals that rather than fixing it, and we will tell you straight when a piece needs replacing instead of restoring. Paired with prompt sealing, the result lasts for years.
Need wood sandblasting in Crescent City or anywhere in Putnam County? Call (386) 800-3366 for a free on-site estimate. You will reach someone who actually does the work, not a call center.
Low-dust wet blasting for sensitive sites and occupied areas.
Tell us about your project and we will get you a clear, no-obligation estimate. You will reach someone who actually does the work.